John Breed, Diary and Training diary, item 98

• March 28, 2017 02:15:54 Cheryl Ellsworth

  NOTE
  

  Should a jam occur after firing, care must be taken 

  to see that the striker is flush with the rear end of the

  striker guide block before force is used upon the breech

  to open the same. In cases where the striker is not

  flush with the guide block, withdraw the keep pin and

  hinge bolt of the breech mechanism lever and remove the

  lever, guide block, firing lever, and striker from the gun

  Replace the breech mechanism lever and hinge bolt

  and swing the breech screw and carrier into the loading

  position then replace the striker, firing lever, and guide block

  
  

  Extractor
  

  The extractor is of steel, and is hinged to the

  right side of the gun. On the inner end are two arms

  which clip the rim of the cartridge, the outer end forming

  a lug by means of which the extractor is automatically

  actuated in opening the breech

  
  

  N.B
  

  When removing the striker from or inserting it

  into the guide block the safety catch in the latter

  must always be in the firing position

  
  

• March 13, 2017 19:53:28 Charlene Price

  NOTE
  

  Should a jam occur after firing, care must be taken 

  to see that the striker is flush with the rear end of the

  striker guide block before force is used upon the breech

  to open the same. In cases where the striker is not

  flush with the guide block, withdraw the keep pin and

  hinge bolt of the breech mechanism lever and remove the

  lever, guide block, firing lever, and striker from the gun

  Replace the breech mechanism lever and hinge bolt

  and swing the breech screw and carrier into the loading

  position then replace the striker, firing lever, and guide block

  
  

  Extractor
  

  The extractor is of steel, and is hinged to the

  right side of the gun. On the inner end are two arms

  which clip the rim of the cartridge, the outer end forming

  
  

  
  

  • Show revision
  • Compare to current version
  • Compare to previous version
• March 13, 2017 19:52:29 Charlene Price

  NOTE
  

  Should a jam occur after firing, care must be taken 

  to see that the striker is flush with the rear end of the

  striker guide block before force is used upon the breech

  to open the same. In cases where the striker is not

  flush with the guide block, withdraw the keep pin and

  hinge bolt of the breech mechanism lever and remove the

  lever, guide block, firing lever, and striker from the gun

  Replace the breech mechanism lever and hinge bolt

  and swing the breech screw and carrier into the loading

  position then replace the striker, firing lever, and guide block

  
  

  • Show revision
  • Compare to current version
  • Compare to previous version
• March 13, 2017 19:50:50 Charlene Price

  NOTE
  

  Should a jam occur after firing, care must be taken 

  to see that the striker is flush with the rear end of the

  striker guide block before force is used upon the breech

  to open the same. In cases where the striker is not

  flush with the guide block, withdraw the keep pin and

  
  

  
  

  • Show revision
  • Compare to current version
  • Compare to previous version
• March 13, 2017 19:50:13 Charlene Price

  NOTE
  

  Should a jam occur after firing, care must be taken 

  to see that the striker is flush with the rear end of the

  striker guide block before force is used upon the breech

  
  

  • Show revision
  • Compare to current version
  • Compare to previous version
• March 13, 2017 19:49:09 Charlene Price

  NOTE
  

  S

  
  

  • Show revision
  • Compare to current version
  • Compare to previous version

Description